CaptureBack overhead scanning - Revision history

Kgmatheny: deprecated

2013-05-23T22:01:59Z

deprecated

←Older revision		Revision as of 22:01, 23 May 2013
Line 1:		Line 1:
		+	'''The information below is rendered in gray font because we no longer use this hardware and software'''
		+
		+
		+	<font color="gray">
		+
	==PhaseOne captureback overhead scanning station:==		==PhaseOne captureback overhead scanning station:==

Jjcolonnaromano at 18:27, 9 November 2010

2010-11-09T18:27:07Z

←Older revision		Revision as of 18:27, 9 November 2010
Line 48:		Line 48:
	##[http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip] - the fix recommended by Phase One.		##[http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip] - the fix recommended by Phase One.
	##* Make sure the patch is run on the drive for the computer to which the Phase One is installed.		##* Make sure the patch is run on the drive for the computer to which the Phase One is installed.
		+	#The camerabody "err db" of which there are a few "db" related errors pertains to either a permissions issue with the directory that the software is trying to write the capture too, or to a lack of sufficient or perception of sufficient disk space on the sessions harddrive. making sure that the permissions are set to write and the disk is adequately empty for the session you are saving to will fix the problem. If you need to clear disk space make sure to empty the session trash folder and system trash bin to free up the space. Also the "err db" error has been seen to accompany the mirror being stuck in the "up" position. to release the mirror you must disrupt electric power to that component of the camera body, this is done by pulling the lens release lock (WHILE HOLDING THE LENS!) or by removing and reseating the batteries from the camerabody.
	<hr>		<hr>

Scpstu32: /* Resources and Links: */

2010-10-29T19:40:55Z

Resources and Links:

←Older revision		Revision as of 19:40, 29 October 2010
Line 51:		Line 51:

	===Resources and Links:===		===Resources and Links:===
		+	# [[Capture_Back]] - internal link to workflow
	# PhaseOne digital camera systems [http://www.phaseone.com/Content/p1digitalbacks/P-,-a-,H-series/P%2045.aspx]		# PhaseOne digital camera systems [http://www.phaseone.com/Content/p1digitalbacks/P-,-a-,H-series/P%2045.aspx]
	# Digital Transitions overhead camera systems [http://www.digitaltransitions.com/]		# Digital Transitions overhead camera systems [http://www.digitaltransitions.com/]
	# Mamiya camera 645AFDIII [http://www.mamiya.com/645afd-iii.html]		# Mamiya camera 645AFDIII [http://www.mamiya.com/645afd-iii.html]

Scpstu32: /* Troubleshooting: */

2010-10-13T13:49:49Z

Troubleshooting:

←Older revision		Revision as of 13:49, 13 October 2010
Line 43:		Line 43:
	#If there is a problem with establishing connection between the camera, digitalback, or software, this can be reset by turning off all three components and restarting them in the following order... software -> digitalback -> camera.		#If there is a problem with establishing connection between the camera, digitalback, or software, this can be reset by turning off all three components and restarting them in the following order... software -> digitalback -> camera.
	#The lens on the camera has an autofocus setting useful for quickly aquiring focus of the subject. However because the large lens is oriented in a vertical position pointed down at the scan table, the weight of the lens will cause the camera to become out of focus as the mirror movement vibrates the camera during secsessive image captures! please make sure the lens is securely fastend after your done focusing and that the lens is set to "MF" manual focus before you begin your capture session		#The lens on the camera has an autofocus setting useful for quickly aquiring focus of the subject. However because the large lens is oriented in a vertical position pointed down at the scan table, the weight of the lens will cause the camera to become out of focus as the mirror movement vibrates the camera during secsessive image captures! please make sure the lens is securely fastend after your done focusing and that the lens is set to "MF" manual focus before you begin your capture session
-	#If the drivers cannot be installed on Windows XP Service pack 2 or 3, it may be necessary to roll the firewire drivers back to Service Pack 1 firewire drivers, according to the phaseone.com's Knowledge Base.	+	#If the drivers cannot be installed on Windows XP Service pack 2 or 3, it may be necessary to roll the firewire drivers back to Service Pack 1 firewire drivers, according to the [http://www.phaseone.com/en/SupportMain.aspx Phase One Knowledge Base].
	#*For more information, see:		#*For more information, see:
	##[http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf] - a description of the problem.		##[http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf] - a description of the problem.

Scpstu32: /* Troubleshooting: */

2010-10-13T13:42:23Z

Troubleshooting:

←Older revision		Revision as of 13:42, 13 October 2010
Line 44:		Line 44:
	#The lens on the camera has an autofocus setting useful for quickly aquiring focus of the subject. However because the large lens is oriented in a vertical position pointed down at the scan table, the weight of the lens will cause the camera to become out of focus as the mirror movement vibrates the camera during secsessive image captures! please make sure the lens is securely fastend after your done focusing and that the lens is set to "MF" manual focus before you begin your capture session		#The lens on the camera has an autofocus setting useful for quickly aquiring focus of the subject. However because the large lens is oriented in a vertical position pointed down at the scan table, the weight of the lens will cause the camera to become out of focus as the mirror movement vibrates the camera during secsessive image captures! please make sure the lens is securely fastend after your done focusing and that the lens is set to "MF" manual focus before you begin your capture session
	#If the drivers cannot be installed on Windows XP Service pack 2 or 3, it may be necessary to roll the firewire drivers back to Service Pack 1 firewire drivers, according to the phaseone.com's Knowledge Base.		#If the drivers cannot be installed on Windows XP Service pack 2 or 3, it may be necessary to roll the firewire drivers back to Service Pack 1 firewire drivers, according to the phaseone.com's Knowledge Base.
-	#*For more information, see	+	#*For more information, see:
	##[http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf] - a description of the problem.		##[http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf] - a description of the problem.
	##[http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip] - the fix recommended by Phase One.		##[http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip] - the fix recommended by Phase One.

Scpstu32: /* Troubleshooting: */

2010-10-13T13:42:08Z

Troubleshooting:

←Older revision		Revision as of 13:42, 13 October 2010
Line 47:		Line 47:
	##[http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf] - a description of the problem.		##[http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf] - a description of the problem.
	##[http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip] - the fix recommended by Phase One.		##[http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip] - the fix recommended by Phase One.
		+	##* Make sure the patch is run on the drive for the computer to which the Phase One is installed.
	<hr>		<hr>

Scpstu32: /* Troubleshooting: */

2010-10-13T13:39:40Z

Troubleshooting:

←Older revision		Revision as of 13:39, 13 October 2010
Line 44:		Line 44:
	#The lens on the camera has an autofocus setting useful for quickly aquiring focus of the subject. However because the large lens is oriented in a vertical position pointed down at the scan table, the weight of the lens will cause the camera to become out of focus as the mirror movement vibrates the camera during secsessive image captures! please make sure the lens is securely fastend after your done focusing and that the lens is set to "MF" manual focus before you begin your capture session		#The lens on the camera has an autofocus setting useful for quickly aquiring focus of the subject. However because the large lens is oriented in a vertical position pointed down at the scan table, the weight of the lens will cause the camera to become out of focus as the mirror movement vibrates the camera during secsessive image captures! please make sure the lens is securely fastend after your done focusing and that the lens is set to "MF" manual focus before you begin your capture session
	#If the drivers cannot be installed on Windows XP Service pack 2 or 3, it may be necessary to roll the firewire drivers back to Service Pack 1 firewire drivers, according to the phaseone.com's Knowledge Base.		#If the drivers cannot be installed on Windows XP Service pack 2 or 3, it may be necessary to roll the firewire drivers back to Service Pack 1 firewire drivers, according to the phaseone.com's Knowledge Base.
-	For more information, see	+	#*For more information, see
-	*[http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf] - a description of the problem.	+	##[http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf] - a description of the problem.
-	*[http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip] - the fix recommended by Phase One.	+	##[http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip] - the fix recommended by Phase One.
	<hr>		<hr>

Scpstu32: /* Troubleshooting: */

2010-10-13T13:30:29Z

Troubleshooting:

←Older revision		Revision as of 13:30, 13 October 2010
Line 43:		Line 43:
	#If there is a problem with establishing connection between the camera, digitalback, or software, this can be reset by turning off all three components and restarting them in the following order... software -> digitalback -> camera.		#If there is a problem with establishing connection between the camera, digitalback, or software, this can be reset by turning off all three components and restarting them in the following order... software -> digitalback -> camera.
	#The lens on the camera has an autofocus setting useful for quickly aquiring focus of the subject. However because the large lens is oriented in a vertical position pointed down at the scan table, the weight of the lens will cause the camera to become out of focus as the mirror movement vibrates the camera during secsessive image captures! please make sure the lens is securely fastend after your done focusing and that the lens is set to "MF" manual focus before you begin your capture session		#The lens on the camera has an autofocus setting useful for quickly aquiring focus of the subject. However because the large lens is oriented in a vertical position pointed down at the scan table, the weight of the lens will cause the camera to become out of focus as the mirror movement vibrates the camera during secsessive image captures! please make sure the lens is securely fastend after your done focusing and that the lens is set to "MF" manual focus before you begin your capture session
-	#If the drivers cannot be installed on Windows XP Service pack 2+, it may be necessary to roll the firewire drivers back to Service Pack 1 firewire drivers. For more information, see [http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf].	+	#If the drivers cannot be installed on Windows XP Service pack 2 or 3, it may be necessary to roll the firewire drivers back to Service Pack 1 firewire drivers, according to the phaseone.com's Knowledge Base.
		+	For more information, see
		+	*[http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf] - a description of the problem.
		+	*[http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip http://www.lib.ua.edu/wiki/digcoll/images/a/ac/XP_SP2_1394_FIX_V2.zip] - the fix recommended by Phase One.
	<hr>		<hr>

Scpstu32: /* Troubleshooting: */

2010-10-13T13:26:51Z

Troubleshooting:

←Older revision		Revision as of 13:26, 13 October 2010
Line 43:		Line 43:
	#If there is a problem with establishing connection between the camera, digitalback, or software, this can be reset by turning off all three components and restarting them in the following order... software -> digitalback -> camera.		#If there is a problem with establishing connection between the camera, digitalback, or software, this can be reset by turning off all three components and restarting them in the following order... software -> digitalback -> camera.
	#The lens on the camera has an autofocus setting useful for quickly aquiring focus of the subject. However because the large lens is oriented in a vertical position pointed down at the scan table, the weight of the lens will cause the camera to become out of focus as the mirror movement vibrates the camera during secsessive image captures! please make sure the lens is securely fastend after your done focusing and that the lens is set to "MF" manual focus before you begin your capture session		#The lens on the camera has an autofocus setting useful for quickly aquiring focus of the subject. However because the large lens is oriented in a vertical position pointed down at the scan table, the weight of the lens will cause the camera to become out of focus as the mirror movement vibrates the camera during secsessive image captures! please make sure the lens is securely fastend after your done focusing and that the lens is set to "MF" manual focus before you begin your capture session
-	#If the drivers cannot be installed on Windows XP Service pack 2+, it may be necessary to roll the firewire drivers back to Service Pack 1 firewire drivers. For more information, see [http://~~xchange~~.~~phaseone~~.~~com~~/~~Content~~/~~Support~~/~~Article.aspx?articleid=~~1696~~&languageid=1~~ http://~~xchange~~.~~phaseone~~.~~com~~/~~Content~~/~~Support~~/~~Article.aspx?articleid=~~1696~~&languageid=1~~].	+	#If the drivers cannot be installed on Windows XP Service pack 2+, it may be necessary to roll the firewire drivers back to Service Pack 1 firewire drivers. For more information, see [http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf http://www.lib.ua.edu/wiki/digcoll/images/d/d3/PhaseOne_articleID-1696.pdf].
	<hr>		<hr>

Scpstu32: /* Troubleshooting: */

2010-01-29T16:58:00Z

Troubleshooting:

←Older revision		Revision as of 16:58, 29 January 2010
Line 43:		Line 43:
	#If there is a problem with establishing connection between the camera, digitalback, or software, this can be reset by turning off all three components and restarting them in the following order... software -> digitalback -> camera.		#If there is a problem with establishing connection between the camera, digitalback, or software, this can be reset by turning off all three components and restarting them in the following order... software -> digitalback -> camera.
	#The lens on the camera has an autofocus setting useful for quickly aquiring focus of the subject. However because the large lens is oriented in a vertical position pointed down at the scan table, the weight of the lens will cause the camera to become out of focus as the mirror movement vibrates the camera during secsessive image captures! please make sure the lens is securely fastend after your done focusing and that the lens is set to "MF" manual focus before you begin your capture session		#The lens on the camera has an autofocus setting useful for quickly aquiring focus of the subject. However because the large lens is oriented in a vertical position pointed down at the scan table, the weight of the lens will cause the camera to become out of focus as the mirror movement vibrates the camera during secsessive image captures! please make sure the lens is securely fastend after your done focusing and that the lens is set to "MF" manual focus before you begin your capture session
-	<hr>
	#If the drivers cannot be installed on Windows XP Service pack 2+, it may be necessary to roll the firewire drivers back to Service Pack 1 firewire drivers. For more information, see [http://xchange.phaseone.com/Content/Support/Article.aspx?articleid=1696&languageid=1 http://xchange.phaseone.com/Content/Support/Article.aspx?articleid=1696&languageid=1].		#If the drivers cannot be installed on Windows XP Service pack 2+, it may be necessary to roll the firewire drivers back to Service Pack 1 firewire drivers. For more information, see [http://xchange.phaseone.com/Content/Support/Article.aspx?articleid=1696&languageid=1 http://xchange.phaseone.com/Content/Support/Article.aspx?articleid=1696&languageid=1].
		+	<hr>

	===Resources and Links:===		===Resources and Links:===